CHA Geography: May 2013

Ask yourself the following questions. If you are confident then great. If not, recap from using the information below:

1) Do you know the four processes of erosion?

2) Do you know the formation of the 3 erosional landforms at the coast?

3) Do you know the four processes of transportation?

4) Do you understand longshore drift?

5) Do you know the 3 landforms formed by deposition at the coast?

A landform is a natural feature of the earth’s surface. Landforms can be created by rivers, glaciers (large masses of moving ice) and the sea.

•In coastal regions, landforms are created (and destroyed) by the power of the sea. A variety of different processes such as erosion, transportation and deposition all help to create these unique landforms which are only found in coastal areas.

Waves are the primary force causing erosion along coastlines. A wave is formed by the wind blowing across the surface of the water, creating ripples, which then grow into waves. As waves reach the coast the lower section slows due to friction. The upper section topples over and breaks forward.
The Fetch determines how powerful a wave may be. It is the distance that the wave has travelled. For instance, a wave hitting the coast of Cornwall may have travelled over 4000 miles to get there, all the way across the Atlantic. However a wave hitting Dover may have only travelled the width of the English Channel.
The Strength Of The Wind also influences the power of the waves, so even those with a relatively short fetch can have a great deal of energy, and there fore cause a lot of damage to the coastline.

Destructive waves vs constructive waves

The coastal system is an ever-changing physical environment, powered primarily by the waves. These come in two main forms: destructive (or erosive) waves, and constructive (or depositional) waves.
1. Destructive Waves have a number of important characteristics:
i) Their backwash is much stronger than their swash, thus allowing them to remove material from the beach.
ii) They are frequent in number, usually between 10 and 15 per minute.
iii) They are tall waves, meaning they have a greater distance to fall when they break. This causes them to scour out the beach material.
iv) Destructive waves create a steep narrow beach.

2. Constructive Waves have a number of important characteristics:
i) Their swash is much stronger than their backwash, causing the beach to be built up by the deposited material.
ii) They are less frequent, reaching shore between 6 and 9 times each minute.
iii) They are long waves and so roll onto the beach rather than crashing onto it.
iv) Constructive waves create a wide, gently sloping beach.

Processes of coastal erosion:

1. Attrition:

"Rock on rock"

Particles carried by the waves crash against each other and are broken up into smaller particles.

2. Corrasion (also known as abrasion):

"Rock on cliff"

Particles carried by the waves crash against the cliffs, eroding the cliffs.

3. Corrosion:

"Rusting / dissolving"

Salt in the seawater slowly dissolves the cliffs.

The material produced is carried away by the process of solution.

4. Hydraulic Action:

"Pressuring"

The water traps air in cracks and caves in the rock.

This air is compressed by the incoming waves placing great pressure on the rocks, causing them to crack eventually.

Erosional Landforms

Headlands and Bays.

Formed on an Atlantic (discordant) coastline due to the softer rock being eroded quicker than the harder rock.

Beaches form in the bays where the soft rock has been eroded away.

Headlands of more resistant, hard rock are left behind.

Cliffs & Wave Cut Platforms

Cliffs are formed when destructive waves attack the bottom of the rock face between high and low water mark.

The area under attack is eroded using the major processes of coastal erosion.

Points of weakness, such as faults and joints are attacked most, and eventually a wave-cut notch is gouged out.

The rock above overhangs the notch, and as it is cut deeper into the rock, gravity causes the overhanging rock to collapse.

The loose rocks are removed by the sea and transported along the coast by long shore drift.

The whole process of undercutting the cliff begins again.

As the cliff is eroded backwards it leaves behind a wave-cut platform, at the level of the low water mark.

This platform is rarely eroded, as the waves energy is concentrated on eroding the area between.

http://www.curriculumbits.com/prodimages/details/geography/cliffs-and-wave-cut-platforms.html
Caves, Arches, Stacks and Stumps
- Mainly seen on headlands.
- Waves start by attacking the main points of weakness in the rock: the joints and faults.
- A point of weakness is increased in size until it becomes a cave
- The waves continue to attack the cave, which finally results in an arch being formed through the headland.
- The arch is attacked both by coastal erosion and sub-aerial erosion and finally the roof of the arch falls into the sea.
- This leaves behind a stack, which is then slowly eroded down to become a stump.the high and low water mark, and not the rock that is underneath them.

Transportation

Long shore Drift

Material is moved along the coastline by the waves.

Waves will often approach the coast at an angle, carrying material with them. This is carried up on to the beach by the swash.

The material is then dragged out to sea by the backwash, but this time it travels at right angles to the beach, as it will roll down the steepest gradient.

This movement will slowly transport material laterally along the coast.

Sediment movement:
Long shore drift is the overall process of transportation, however the material actually moves through the four transportation processes seen in rivers. These depend on the size of sediment:
i) Traction - the rolling of large material along the sea floor by the waves.
ii) Saltation - the bouncing of slightly lighter material along the sea floor.
iii) Suspension - Small particles of material carried by the water.
iv) Solution - Material is dissolved and carried by the water.

Coastal Deposition:

The process associated with constructive waves.

Material is dropped by waves once they lose energy, either by rolling up a beach or where a river estuary causes a disruption to the normal movement of material along the coast.

Creates features such as beaches, spits, bars and tombolos.

Spits are also created by deposition. A spit is an extended stretch of beach material that projects out to sea and is joined to the mainland at one end.

Spits are formed where the prevailing wind blows at an angle to the coastline, resulting in longshore drift. An example of a spit is Spurn Head, found along the Holderness coast in Humberside.

http://www.bbc.co.uk/learningzone/clips/the-formation-of-spits/3246.html

Week commencing	Tier and topic
6^th May	Foundation: Ecosystems
13^th May	Higher: Ecosystems
20^th May	Foundation: Desertification
3^rd June	Higher: Desertification
10^th June	Foundation: Rivers
17^th June	Higher: Rivers
24^th June	Foundation: Coasts
1^st July	NOT ON!
8^TH July	Higher: Coasts

CHA Geography

Pages

Monday, 20 May 2013

Year 7: Coasts

Thursday, 2 May 2013

Geographical Games

Geography Documentaries of the Week: Check these out as a relaxed way to aid revision:

Crazy Coasts: Processes & Landforms

Destructive waves vs constructive waves

Geography Club

Welcome

What would you like to do more of in geography lessons?

About Me

Web Links

Total Pageviews